Jump to content
Japanese Modelling & Japan Rail Enthusiasts Forum
JanW

My new track coming to life

Recommended Posts

Here a small update of my project. I finally got the woodwork of the table ready and fitted the tracks. All seems to work out fine. Now wiring can start in earnest.

IMG_4254.JPG

IMG_4252.JPG

  • Like 11

Share this post


Link to post
Share on other sites

Looks fantastic jan,I love the wiring.It s a bit fiddly but very rewarding when things work.

Share this post


Link to post
Share on other sites

Nice it’s coming to gether Jan! Like how the like how the viaduct is a single Loop with the station in the center.

 

going to be doc or dc?

 

cheers

 

jeff

Share this post


Link to post
Share on other sites

Very nice layout :) Ours are a bit similar, especially with the viaduct station. 

 

I'm also on the wiring phase and it's stressing me out hardcore... I'm scared that drilling the holes and everything is too final and I might regret it... Let me know how yours goes, especially with the viaduct station... I have no idea how I'm going to wire the turnouts up there.

 

Cheers! 

Share this post


Link to post
Share on other sites
Posted (edited)

Tt,

 

what are you using for your layout base/support? No reason it can't have a bunch of mistake holes in it is there? They will just get covered up eventually with scenery. You can always patch mistakes with foam spray or that foam paste that woodland scenics sells. Wires can be moved, cut and spliced easily when needed.

 

Don’t worry about making a wiring mistake as they are pretty easy to just redo to get it right. It’s really part of the process of learning to screw a few things up and these are pretty low pressure things (unlike say gumming up points with plaster). You can try to plan a huge amount to get it just right, but this may stress you out and drive you crazy. I usually opt for the middle route of planning some but then just getting going and realizing I may have to adapt some on the fly and fix, and learn from, a couple of boo boos for the next time!

 

layouts are always an evolution within each one and layout to layout! Enjoy the process if you can and try not to let it stress you.

 

cheers

 

jeff

Edited by cteno4
  • Like 1

Share this post


Link to post
Share on other sites

Wow, amazing work Jan!  I cant wait to see the progress on this layout.

Share this post


Link to post
Share on other sites

Nice layout! One thing: Having a crossover between two island platforms might have some clearance issues with the outer ends of longer coaches hitting the platform edges. 

Share this post


Link to post
Share on other sites
On 1/3/2018 at 7:18 AM, kvp said:

Nice layout! One thing: Having a crossover between two island platforms might have some clearance issues with the outer ends of longer coaches hitting the platform edges. 

Thanks a lot for spotting this. Someone else mentioned that as well. So I tested it and it isn't an issue with the normal commuter trains. Only the long-nosed Shinkansen trains have an issue. 
Background: I grew up in Zwolle, a provincial capital in the Netherlands. My parental home was right in front of the railway station, se we often ventured onto the platforms and watched the trains arriving and departing. This station had/has also a cross-over at the platforms, exactly like my lay-out. I regard it a bit as something a proper station ought to have ;-) 

  • Like 2

Share this post


Link to post
Share on other sites

In the mean time I testrun the various trains along the tracks to see if there any issues, like derailing, too steep inclinations etc. I now found that running the trains creates more noise that I hoped for. I purposely designed to table structure to have maximum rigidity at the point where the tracks are, using 12 mm multiplex stiffeners between the lower plate and the upper table top (see pic).  So I tested to use thin felt (1 mm) between the tracks and the table top. That reduces noise a lot. So before running the wiring, I intent to try and reduce train running noise. 
I will also try to install the felt in the overhead train station although it may add complications at the ends where the tracks connect up to the viaduct. At these ends I doubt I can squeeze 1 mm felt between the track and the station floor.  

Asakusa treintafel doorsnede.jpg

  • Like 1

Share this post


Link to post
Share on other sites
On 1/5/2018 at 2:22 PM, JanW said:

So I tested to use thin felt (1 mm) between the tracks and the table top. That reduces noise a lot.

 

In my layouts I have used 1 mm cork, available in rolls, for this purpose. Cheap to buy from hardware stores as used for covering floors before tiles or flooring are laid on top. Also gives you something to dig into to hide the join between buildings and the ground level.

 

Also I put rubber blocks between the layout frame and supports or tabletop as noise isolation. I use a specialist automotive material used in building Li-Ion batteries for EVs but the same type of material is also easily found as in-soles for sport shoes where used to cushion the feet under repeated impact.

Share this post


Link to post
Share on other sites

I have now put felt below the tracks for noise reduction. Indeed quite effective. I had not thought about cardboard.

IMG_4282.thumb.jpg.131e4b58574d805c5cdda852c48d3fd2.jpg

  • Like 3

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


×